How to Find and Relight a Furnace Pilot Light
Posted on by Shon Mitchell
A furnace pilot light is small, but it starts the heating cycle by igniting gas at the main burner. If your furnace pilot light is out, look near the bottom of the furnace front, behind its access panel. Relighting steps vary by furnace, so follow the instructions on your unit.
No heat can be unsettling, especially when you’re unsure where to start. The pilot light’s location and role offer useful clues: its small flame lights the main burner, but a draft, blockage, or faulty part can keep it from staying lit.
Learn how to find the pilot, understand how it ignites the burner, and safely relight it when your furnace instructions allow. You’ll also learn what common causes and flame colors can indicate, and when to have the furnace inspected.
Key Takeaways
- Look near the bottom of the furnace front, behind the access panel, to find a standing pilot light.
- The pilot flame ignites gas at the main burner; drafts, dirt, or a faulty thermocouple can keep it from staying lit.
- A steady blue flame is the expected pattern. Orange or yellow coloring can point to an issue that needs attention.
- Follow the furnace’s relighting instructions, wait five minutes after turning the pilot to Off, and stop if you smell gas.
Common causes of a pilot light going out
- Check for a draft. Notice whether the pilot goes out after a door opens, a window is left ajar, or air moves near the furnace. A draft can disturb the small flame, especially if the access panel is loose or air reaches the pilot. Don’t block furnace vents or alter the appliance to stop airflow. Follow the manufacturer’s instructions for checking the panel and relighting the pilot.
- Look for signs of dirt or blockage. A dirty or clogged pilot opening can disrupt the flame and prevent it from burning steadily. Dust and debris may also restrict oxygen around the pilot. Observe the flame without touching the burner assembly. If the opening looks obstructed or the pilot repeatedly goes out, arrange a furnace inspection instead of probing the pilot orifice.
- Consider a thermocouple problem. The thermocouple senses heat from the pilot and helps control the gas supply. If it’s bent, broken, or failing, it may not detect the flame correctly. The pilot can then go out or fail to stay lit long enough to ignite the main burner. Note whether the flame dies shortly after you release the control, and share that detail with the technician. Don’t bend or adjust the component yourself.
- Take repeated outages seriously. A furnace safety valve is designed to stop gas from reaching the pilot when its flame goes out. The U.S. Consumer Product Safety Commission warns that a failed gas-control safety valve could allow unburned gas to flow into the furnace, creating an explosion hazard. If you smell leaking gas, don’t try to locate the valve. Immediately contact your gas supplier, as the commission advises.
- Schedule preventive maintenance. A yearly furnace tune-up in the fall, before heating season, can help identify a dirty pilot or worn component. Mention any recurring outages, drafts, or changes in the flame during the appointment, or visit bbairconditioning.com to see what comprehensive heating tune-ups and system inspections involve.
How a furnace pilot light ignites the main burner
- Identify the ignition type. Check the furnace label or manual for its ignition instructions. A visible flame that stays lit between heating cycles indicates a standing pilot. Some furnaces installed before 2010 have standing pilots; a furnace without a continuously burning pilot uses electronic ignition.
- Understand the ignition sequence. When the thermostat calls for heat, gas reaches the main burner. The pilot’s small flame ignites that gas, starting the burner’s heating cycle. If the pilot is out, it can’t light the main burner. A thermocouple helps shut off the gas if the pilot flame goes out.
- Use the instructions for your exact furnace. Relighting steps vary by brand and model because controls and access panels differ. Read the appliance label or manufacturer’s manual before touching a knob or button. Don’t assume instructions for another furnace apply to yours.
- Respond safely to a gas odor. If you smell leaking gas near the furnace, don’t try to locate the valve or relight the pilot. Immediately contact your gas supplier, as the U.S. Consumer Product Safety Commission advises.
- Wait before relighting. After turning the pilot control to Off, wait five minutes before attempting ignition. This gives gas time to dissipate. Then follow the manufacturer’s relighting directions rather than improvising.
- Stop after repeated failed attempts. If the pilot won’t light or stay lit after repeated attempts, stop and call an HVAC technician. A thermocouple, pilot opening, or another furnace component may need attention.
- Keep the furnace off if its pilot is out. Don’t bypass safety controls or try to force the main burner to ignite. The safety valve is designed to cut off gas to the pilot when its flame goes out. Follow the manufacturer’s instructions to determine the next safe step.

Pilot flame color and inconsistent burning
- Observe the flame before changing anything. Use the furnace’s viewing opening, if it has one, and keep your hands clear. Note the flame’s color and whether it stays steady or changes while the pilot is lit. For example, record whether it starts blue, turns yellow, or goes out. These details help distinguish a stable flame from inconsistent burning.
- Compare its color with a steady blue flame. A lit furnace pilot should have a small blue flame. If yours stays blue and steady, it matches the expected appearance. Don’t judge from a quick glance: watch long enough to notice changes in color or shape. If the flame shifts between blue and yellow, note the variation rather than assuming it’s normal.
- Treat yellow or orange as a warning sign. A yellowish flame may indicate inconsistent burning, while orange or yellow can point to a pilot-light or gas-supply problem. Shut off the furnace and have a professional inspect it. Don’t keep relighting it to see if the color improves. Describe the color clearly when arranging a repair.
- Track changes in the flame’s behavior. Note whether it flickers, changes color, or disappears during a heating cycle. A pilot that won’t stay lit is different from one that stays lit but burns yellow. Write down when the change occurs, such as after the furnace starts, and whether it happens again. This gives a technician a useful starting point.
- Look for visible dirt without disturbing the pilot assembly. Dirt and debris can restrict oxygen around the flame and prevent consistent burning. Check the accessible area for visible buildup, but don’t probe the pilot opening or adjust gas components. If debris appears near the assembly, or the flame remains yellow or uneven, stop using the furnace and arrange a professional inspection.
How do I safely relight a furnace pilot light?
- Confirm your furnace has a standing pilot. Check its label or manual first. Some newer furnaces use electronic ignition and don’t have a pilot flame to relight manually. If the instructions don’t describe a standing pilot, don’t try these steps. Follow the guidance for your specific furnace model instead.
- Find the pilot and controls. On many gas furnaces, the pilot is near the bottom of the front, behind an access panel. Read the manufacturer’s instructions to identify the pilot orifice, gas-control knob, and any red button. Don’t guess which control to turn.
- Set the gas-control knob to Off. Follow your furnace’s relighting directions, then wait five minutes before proceeding. This gives gas time to dissipate. If you smell leaking gas, stop and contact your gas supplier. Don’t attempt to light the pilot.
- Switch the knob to Pilot and prepare the ignition. Use a long match or grill lighter at the pilot-light orifice if the manufacturer directs you to do so. Keep the red button pressed while lighting the pilot. Don’t use this manual method if your furnace instructions specify a different procedure.
- Hold the red button after the flame catches. Keep pressing it for at least 60 seconds to help the pilot stay lit. Then release the button and observe whether the flame remains burning. If it goes out, don’t keep making repeated attempts.
- Restore the gas-control setting. Once the pilot stays lit, turn the gas valve knob to On, following the furnace manual. If the pilot won’t light or remain lit after repeated attempts, stop and arrange furnace service. Get help with furnace service if relighting doesn’t resolve the problem.
A draft can blow out a furnace pilot, so follow the manufacturer’s instructions when relighting it. The thermocouple is a safety feature that shuts off gas if the pilot goes out. If the pilot remains unlit after repeated attempts, a technician may need to inspect the furnace.
ProServ Las Vegas: AC Repair
ProServ Las Vegas provides Heating Tuneup / Maintenance for homeowners whose furnace pilot won’t stay lit or needs professional attention. A pilot-light issue involves the heating system, so AC Repair isn’t the right service to diagnose it. If relighting fails, the flame goes out again, or its color looks abnormal, stop troubleshooting and arrange furnace service.
During a heating tune-up, a technician can assess the furnace and identify maintenance needs. Share what you observed, such as repeated outages, a flame that changes color, or a pilot that won’t stay lit after you follow the manufacturer’s instructions. Clear details help focus the visit on the problem.
If your furnace still won’t operate reliably, contact ProServ Las Vegas about Heating Tuneup / Maintenance. ProServ Las Vegas serves homeowners in Las Vegas, Henderson, and North Las Vegas.
Plan your next step with confidence
A recurring ignition problem should be addressed before you rely on the furnace for steady home comfort. If your furnace pilot light goes out again, don’t treat repeated relighting as a lasting fix. Arrange professional attention so the underlying issue can be assessed and the next step identified.
ProServ Las Vegas offers Heating Tuneup / Maintenance for furnace upkeep, along with AC Repair and New A/C Install / Replacement for other home comfort needs. Choose the service that fits the system requiring attention, and share what you’ve observed about the furnace.
Contact ProServ Las Vegas for help with your home comfort needs. Taking a clear next step can help you feel prepared for the heating season ahead.
Frequently Asked Questions
Where is the pilot light on a furnace?
On a gas furnace with a standing pilot, look near the lower front, behind its access panel. A small viewing window may let you see the flame without removing the panel. Check the furnace label or manual to identify the correct access point. If you don’t see a pilot flame, your furnace may use electronic ignition instead, so don’t try to light an assumed pilot.
Why does a furnace pilot light keep going out?
A draft, restricted pilot opening, or faulty thermocouple can cause repeated outages. Notice the timing: does the flame go out after you release the control, or later during furnace operation? Record the pattern and any visible flame changes. If your furnace pilot light goes out repeatedly, avoid repeated relighting attempts and share your observations with a technician. A recurring outage calls for finding the cause, not just restoring the flame.
Can a dirty pilot orifice or faulty thermocouple cause the pilot light to go out?
Yes. Debris at the pilot orifice can disrupt the flame, while a damaged thermocouple may fail to sense its heat and keep the gas supply open. Don’t probe the orifice or bend the thermocouple to test it. Instead, note whether the flame looks weak or won’t stay lit, then share those details with a technician for inspection.
Categories: Uncategorized

